Jan 1 00:00:11 kernel: Creating 1 MTD partitions on "brcmnand": Jan 1 00:00:11 kernel: Options: NO_AUTOINCR,NO_READRDY,BBT_SCAN2NDPAGE, Jan 1 00:00:11 kernel: Available 7 bytes at (off,len): Jan 1 00:00:11 kernel: Spare area=64 eccbytes 56, ecc bytes located at: Jan 1 00:00:11 kernel: Registering the dns_resolver key type Jan 1 00:00:11 kernel: Creating 4 MTD partitions on "nflash": Jan 1 00:00:11 kernel: nflash: squash filesystem with lzma found at block 28 Jan 1 00:00:11 kernel: bcmsflash: found no supported devices Jan 1 00:00:11 kernel: pflash: found no supported devices Jan 1 00:00:11 kernel: Dquot-cache hash table entries: 1024 (orbytes) Jan 1 00:00:11 syslog: module vfat not found in p Jan 1 00:00:11 syslog: module fat not found in p Jan 1 00:00:11 kernel: PCI: Fixing up bus 2 Jan 1 00:00:11 kernel: PCI: Fixing up bus 1 Jan 1 00:00:11 kernel: PCI: Fixing up bus 0 Jan 1 00:00:10 kernel: bio: create slab at 0 Jan 1 00:00:10 kernel: Found a AMD NAND flash: Jan 1 00:00:10 kernel: CPU1: Booted secondary processor Jan 1 00:00:10 kernel: Mount-cache hash table entries: 512 Jan 1 00:00:10 kernel: External imprecise Data abort at addr=0x0, fsr=0x1c06 ignored. Jan 1 00:00:10 kernel: Virtual kernel memory layout: Jan 1 00:00:10 syslog: module leds-usb not found in p Jan 1 00:00:10 syslog: module ledtrig-usbdev not found in p Jan 1 00:00:10 kernel: Kernel command line: root=/dev/mtdblock2 console=ttyS0,115200 init=/sbin/preinit earlyprintk debug Jan 1 00:00:10 kernel: Built 1 zonelists in Zone order, mobility grouping on. Jan 1 00:00:10 kernel: Memory policy: ECC disabled, Data cache writealloc Jan 1 00:00:10 kernel: Machine: Northstar Prototype Jan 1 00:00:10 kernel: CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache Jan 1 00:00:10 kernel: CPU: ARMv7 Processor revision 0 (ARMv7), cr=10c53c7f Here is last thirty lines of log file.Thanks again for all your help !!!Įrsion 2.6.36.4brcmarm (gcc version 4.5.3 (Buildroot 2012.02) ) #21 SMP PREEMPT Thu Nov 21 15:05: Set the time to EST but it continues to show date and time in December / January. Nothing ! Also, shouldn't this router have some type of accurate clock ? The log file is a TXT file you can open with Notepad, and Mark, Copy & Paste it to a message here.įollowed your instructions to the letter. You can “Mark (highlight), Copy (CTRL C) & Paste (CTRL V)” the last 25-30 lines of it to a post here or do the same thing with the log file itself. If it still fails, continue with the setup and then save the System Log. The next page should be the USB Modem page – again, Asus has made it Plug & Play, all you should have to do is click Connect! Wait three to five minutes and it should figure it out. #Verizon pantech uml295 driver password#I can’t remember the particulars, but I think you press Go and the next page you setup an Admin password so do that. Open a browser, it should figure out to use the Ethernet connection and the router’s Quick Internet Setup page should open. Turn off any wireless connection on the computer. Reset the router by pressing and holding the reset button for 5 to 10 seconds and release. You’re welcome! Good feedback! Try this: Disconnect everything from the Asus except one Ethernet cable between a computer and a LAN port.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |